Motor Drivers
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
230,00 EGP- 🔁 16-channel PWM control (12-bit resolution)
- 🔌 I2C interface – only 2 pins needed
- 🧠 Chain up to 62 modules (992 outputs total)
- ⚙️ Adjustable PWM frequency (up to 1.6 kHz)
- ⚡ 3.3V and 5V logic compatible
- 🔧 Output enable pin for quick shutdown
- 🛡️ Reverse polarity protection
- 💡 Power indicator LED
- 🧩 Plug in up to 16 servos directly
A4988 Stepper Motor Driver
75,00 EGP- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
CNC Shield V3.0 For Arduino Uno
125,00 EGP- Four A4988 Drivers: Reliable stepper motor control with up to 2A per coil.
- Microstepping Support: Up to 16 microsteps for smooth and precise motion.
- Adjustable Current Limit: Fine-tune motor performance and protection.
- Heat Sink Compatible: Provisions for heat sinks to manage temperature.
- Arduino Compatibility: Works with Arduino Uno, Nano, and other boards.
- Clear Connections: Easily labeled for simple wiring and setup.
- GRBL Firmware Support: Compatible with popular CNC software.
DRV8825 Stepper Motor Driver with Heat Sink
120,00 EGP- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
L293D Motor Driver Board
120,00 EGPL293D Motor Driver Board
1. Motor Driver IC: Dual L293D H-Bridge
2. Current per Channel: 0.6A
3. Motor Outputs: 4 DC motors or 2 steppers
4. Servo Ports: 2 (pins 9 & 10)
5. Logic Control Voltage: 4.5V–5.5V
6. Motor Input Voltage: 7V–12V DC
L298N DUAL FULL-BRIDGE DRIVER
55,00 EGP✅ Dual Full-Bridge (H-Bridge) Driver
✅ 46V, 2A Continuous per Channel
✅ Drives DC motors, stepper motors, and inductive loads
✅ TTL/CMOS Compatible Inputs
✅ Built-in Diode and Thermal Protection
✅ Ideal for Arduino, Raspberry Pi, and Robotics
-5% New 
-5% OFF
L298N Motor Driver Module – 2A Dual Channel
Original price was: 95,00 EGP.90,00 EGPCurrent price is: 90,00 EGP.- Logical voltage: 5V
- Drive voltage: 5V-35V
- Logical current: 0-36mA
- Drive current: 2A (max. single bridge)
- Max power: 25W
- Dimensions: 44 x 44 x 28 (LxWxH)mm
- Weight: 26 gm
Mini 5A PWM DC Motor Speed Controller – 3V-35V, 90W Max, LED Dimmer
85,00 EGP- Input Voltage Range: 3V to 35V DC
- Max Output Power: Up to 90W
- Current Capacity: Up to 5A continuous
- PWM Control for precise speed and brightness adjustment
- Compact Design suitable for DC motors, fans, and LED dimming projects
ULN2003 Driver Module Stepper Motor Driver Board
40,00 EGP- Uses ULN2003A Darlington driver chip
- Compatible with 5V–12V stepper motors
- 4-phase LED indicators for motor status
- Directly supports 28BYJ-48 stepper motor (XH-5P connector)
- Easy connection to Arduino or other microcontrollers
- Compact and plug-and-play design
Recently Viewed Products
Ekostra Electronics | Microcontrollers, Sensors & 3D Printing Supplies
Shop top-quality Arduino, ESP32 & hardware in Egypt. Build your DIY and engineering projects with fast local shipping and cash on delivery.
